Enterasys-networks X-Pedition 2000 Manuale Utente Pagina 76
- Pagina / 86
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Upgrading the VFS
60 Enterasys X-Pedition 2000 Getting Started Guide
Upgrading the VFS
A VFS file system called VFS2 is available. VFS2 dramatically decreases the time required for
deleting and adding system images.
Note: Upgrading the file system to VFS2 will not erase your configuration image.
The VFS2 file system is only compatible with:
• boot PROM version v.1.1.0.8
• system image version 3.1 or later
To upgrade the VFS file system to VFS2, perform the following steps:
1. Upgrade the firmware to release version 3.1 or later.
2. Upgrade the bootprom to version v.1.1.0.8. See Loading Boot PROM Firmware on page 59 for
instructions on upgrading the firmware.
3. Reboot.
4. Press esc during bootup to enter the bootprom mode.
5. Type pcmakeversion2 to convert your old VFS1 flash card into a new VFS2 file system.
6. Reboot.
Activating Configuration Changes and Saving the
Configuration File
The XP-2000 uses three special configuration files:
• Active – The commands from the Startup configuration file and any configuration commands
that you have made active from the scratchpad (see below).
Caution: The active configuration remains in effect only during the current power cycle. If you
power down or reboot the XP-2000 without saving the active configuration changes to the Startup
configuration file, the changes are lost.
• Startup – The configuration file that the XP-2000 uses to configure itself when the system is
powered on.
• Scratchpad – The configuration commands you have entered during a management session.
These commands do not become active until you explicitly activate them. Because some
commands depend on other commands for successful execution, the XP-2000 scratchpad
simplifies system configuration by allowing you to enter configuration commands in any order,
even when dependencies exist. When you activate the commands in the scratchpad, the
XP-2000 sorts out the dependencies and executes the command in the proper sequence.
- Getting Started Guide 1
- Revision Date: 02.28.2003 1
- FCC NOTICE 3
- INDUSTRY CANADA NOTICE 3
- VCCI NOTICE 3
- CLASS A ITE NOTICE 3
- BSMI EMC STATEMENT — TAIWAN 3
- SAFETY INFORMATION 4
- CLASS 1 LASER TRANSCEIVERS 4
- ENTERASYS NETWORKS, INC 5
- PROGRAM LICENSE AGREEMENT 5
- DECLARATION OF CONFORMITY 8
- Contents 10
- About this Guide 13
- Related Documentation 14
- Getting Help 14
- Chapter 1 17
- Features Overview 17
- Specifications 18
- Features 19
- Bridging 20
- Port and Protocol VLANs 20
- Layer-4 Switching 22
- Security 22
- Quality of Service 23
- Statistics 23
- Management Platforms 23
- Hardware Overview 24
- Motherboard Features 25
- Power Supplies 26
- Expansion Modules 27
- G2M-HFXA4-08 100BASE-FX 29
- 1000BASE-SXG2M-GSXA1-02 30
- 1000BASE-LXG2M-GLXA9-02 32
- Dual SerialG2M-SERAC-02 34
- Quad Serial - CG2M-SECAC-04 35
- Dual HSSI 36
- G8M-HSIAC-02 36
- LED Description 37
- Chapter 2 39
- Hardware 39
- Installation 39
- Hardware Specifications 40
- Installing the Hardware 40
- Verifying Your Shipment 41
- Installing the Chassis 42
- Front of XP-2000 46
- Attaching Port Cables 50
- Chapter 3 59
- Firmware 59
- Installation and 59
- Access Modes 60
- Basic Line Editing Commands 61
- Setting Up Passwords 67
- Setting SYSLOG Parameters 69
- <IP-addr> 71
- Loading System Image Firmware 72
- Here is an example: 74
- Loading Boot PROM Firmware 75
- Upgrading the VFS 76
- Configuration File 76
- P: stp enable et.*.* 78
- Appendix A 79
- Troubleshooting 79
- Appendix B 81
- Technical Support 81
Prodotti e manuali riguardandi Hardware Enterasys-networks X-Pedition 2000
(110 pagine)Isp-technologies SA118 manuales
Manuales del propietario y guías del usuario para Audio Isp-technologies SA118.
Ofrecemos 1 manuales en pdf Isp-technologies SA118 para descargar gratis por tipos de documentos: Manual de usuario
Commenti su questo manuale